Science and Fashion Meet! Craft DIY Bracelets for Kids

July 24, 2017

Fun and Glitter are the whole point of crafts, right? Cute DIY jewelry ideas for girls are right here and a bit of science thrown in the mix. It's party time! This is the perfect birthday party project for girls. Let's go!

Courtesy of Babble Dabble Do we are going to make Tubular Glitter Bracelets. They are so easy and fun to make and where Science meets Fashion! Yes, you read that correctly, science meets fashion! Did you ever think those two concepts could be combined in one kid’s craft project? Neither did I, but when I found a lovely idea for making glitter tubes in Science Arts: Discovering Science Through Art Experiences I decided they would also make great jewelry for kids!

There are two different versions here, because well, I just couldn't decide which I loved more, so go ahead. Make both!

Totally Tubular Science Bracelets

Materials

  • Plastic Tubing:
    • 4 to 5 feet of 7/16″ Outer Diameter (OD) recommended. Plastic tubing is available at your local hardware store.
    • 1 foot of tubing whose OD matches the Inner Diameter of the 7/16″ tubing- this will be the “plug” for the bracelet. It needs to be very snug. If you can’t find matching tubes see the plug alternative below*
  • Large Glitter (your typical glitter, avoid using fine glitter)
  • Small Beads or Objects to fit within the tube (I used Perler beads)
  • Cooking Oil
  • Painters Tape
  • Clear Tape (optional)
  • Funnel
  • Water
  • Paper Towels

 

Instructions

  • Step One Cut your larger tubing: 8″ long for little folks’ wrists and about 9-1/2″ long for adults.
  • Step Two Cut about an inch of smaller tubing for the plug. If you couldn’t find tubing with the right diameter for the plug see below for an alternative*.
  • Step Three Fit the smaller tubing into one end of the larger tube. If you’re having trouble, take some cooking oil and dab it on the end of the small tube. It should slide in the larger tube more easily.
  • Step Four Put a piece of painter’s tape on the end of the plug.
  • Step Five Place the funnel on the other end of the large tube and tape around the connection point.

  • Step Six Fill it! The beads should be added one at a time so as not to get stuck in the end of the funnel. This is a great fine motor skills activity. Glitter can be shaken into the funnel. When the tube is half or three quarters full, stop.
  • Step Seven Remove the funnel and tape at both ends of the tubing. Make sure you are holding the tube in a “U” shape so the filling doesn’t come spilling out.

 

  • Step Eight Add water! You’ll want to place the large end of the tubing under a faucet and fill ever so slightly. Leave some air within the tube so the water can float around freely.
  • Step Nine Take the plug end of the tubing and wrap it around to meet the other end of the bracelet. Insert the plug. Use oil again if you are having a hard time.
  • Step Ten Dry off any excess water on the bracelet. You can place some clear tape around the connection point to prevent leakage. If you can get away without using tape the bracelet will look prettier, so get that connection snug!
  • *Plug Alternative Cut a small piece (1/2″ to 1″) of the same sized tubing you are using for the bracelet to act as the plug. Now cut a slit down the length of this piece. Curl the tubing in on itself until it fits within the longer section of tubing. If it still doesn’t fit, cut about an 1/8″ off the entire length of the tubing, then curl it in and insert. IMPORTANT You want this to be super snug so that it doesn’t leak, so do you darnedest to squeeze it in there!
  • You’re done! When you rotate the bracelet, the glitter and beads will float around the tubing. For fun variations add soap and or food coloring to the tube before sealing.

    HOW IS THIS SCIENCE? This is a simple way to illustrate density. The glitter floats freely around the tube because it is less dense and flat. It’s shape and density make it easy for the water to push it around the tube.  The beads are denser and have a hole in the center so they are harder for the water to push through the tube. If the beads and glitter were the same size you’d have the perfect science illustration BUT this is good for starters…I think this would be a good project to make alongside the classic science experiment Floaters and Sinkers. I’m a big believer in simple visual projects to illustrate concepts to kids rather than hard to understand verbal explanations! 

    Okay so now that you’ve tackled the science version of this project, ready to tackle the fancy one?

    Totally Tubular Glitter Bracelets

  • Materials

    • Plastic Tubing: 4 to 5 feet of thin tubing- 3/16″ OD or more
    • Fine Colored Glitter such as this neon set by Martha Stewart 
    • Cooking Oil
    • Painters Tape
    • Paper

    The main difference between this version and the last is that you will not be adding water. The smaller tubing is hard to fill and it only takes a small amount of glitter to completely fill these tubes. So just make them pretty!

    Instructions

    • Step One Cut your tubing: 8″ for little folks and about 9 1/2″ long for adults.
    • Step Two Cut about a 1/2″ of tubing for the plug and insert it into one end of the long piece of tubing. See “Plug Alternative” directions above for how to do this*. Dab cooking oil on the plug to make it easier to insert.
    • Step Three Put a piece of painter’s tape on the end of the plug.
    • Step Four Make a small funnel out of a paper scrap and tape it to the other end of the tube at the connection point.
    • Step Five Fill it! Shake your fancy glitter into the funnel. It won’t take much to fill the small tube, a couple of shakes and you’re good to go. Add as many colors as you want to create a design.
    • Step Six Make sure to gently shake the tube each time you add glitter so that it sinks to the bottom. Otherwise your colors will get mixed quickly.
    • Step Seven Remove the funnel and tape at both ends of the tubing. Make sure you are holding the tube in a U shape so the filling doesn’t come spilling out.
    • Step Eight Take the plug end and wrap it around to meet the other end of the tubing. Plug. Use oil again if you are having a hard time inserting the smaller tube.
  •  

     You’re done! You don’t really need to tape around the connection point unless you feel the tubing is going to come apart. The tape detracts from the design so use it only when necessary.

    You’re done! You don’t really need to tape around the connection point unless you feel the tubing is going to come apart. The tape detracts from the design so use it only when necessary.

    Such fun! Little girls and big girls love jewelry. It's just a fact of life! We create safe and beautiful jewelry for your daughters, we are moms and we care to make to perfect for her.

    Hypoallergenic, comfortable lever back, 18k gold plated, Lead free, Nickel free and Cadmium free jewelry. Go ahead, make her smile!




    Leave a comment

    Comments will be approved before showing up.